XAG P150 Standard 7KW 6B2C Kit
XAG P150 Standard 7KW 6B2C Kit is a Robot from XAG. Spray width: 5–10 m
XAG P150 Standard 7KW 6B2C Kit technical overview
XAG P150 Standard 7KW 6B2C Kit is a Robot from XAG. Spray width: 5–10 m
Spray tank: 80 L / 80 kg payload
Before purchase, confirm the exact model or part number, configuration, compatible accessories and included scope against the written quotation and manufacturer documentation.
Three checks before purchase
Match the manufacturer model, part number and product-label details to the quotation.
Review system, accessory, software, power and installation requirements that apply to this product.
Confirm included items, condition, warranty, documentation and delivery terms before payment.
XAG P150 Standard 7KW 6B2C Kit images
Use the product media and exact-unit photographs supplied with the quotation to confirm model, configuration and condition.
Important XAG P150 Standard 7KW 6B2C Kit details
These points summarize model-specific technical information available for product evaluation.
Spray width: 5–10 m
Spray width: 5–10 m
Spray tank: 80 L / 80 kg payload
Spray tank: 80 L / 80 kg payload
Max takeoff weight: 136 kg (spraying) / 140 kg (spreading)
Max takeoff weight: 136 kg (spraying) / 140 kg (spreading)
Hovering precision with RTK enabled: ±10 cm (horizontal), ±10 cm (vertical)
Hovering precision with RTK enabled: ±10 cm (horizontal), ±10 cm (vertical)
The same listing also describes granular spreading capacity (when configured with a
The same listing also describes granular spreading capacity (when configured with a spreader module), including a 115 L granule container, up to 300 kg/min spread rate, and 5–9 m spread width, along with radar detection range details.
Where XAG P150 Standard 7KW 6B2C Kit can fit
Suitability depends on the exact configuration, compatible systems, intended professional use and manufacturer instructions.
Robotics deployment
Evaluate XAG P150 Standard 7KW 6B2C Kit for the robotics workflow supported by its exact hardware, payload and software configuration.
Software and systems integration
Confirm controller, SDK/API, network interfaces, sensors and supported third-party integrations.
Operational fit
Match payload, mobility, reach, runtime, environment and safety requirements to the intended task.
Commissioning and support
Confirm charging/power, accessories, training, spare parts and acceptance testing before deployment.
XAG P150 Standard 7KW 6B2C Kit specifications and identification
The table summarizes confirmed model and technical information from product specifications and available technical documentation. Configuration-sensitive values should be checked against the exact supplied unit.
- Product
- XAG P150 Standard 7KW 6B2C Kit
- Manufacturer / brand
- XAG
- Model / part reference
- XAG P150 Standard 7KW 6B2C Kit
- Equipment type
- Robot
- Maximum flight speed
- 18 m/s (noted with footnote context)
- Hovering precision with RTK enabled
- ±10 cm (horizontal), ±10 cm (vertical)
- Rated takeoff weight (spraying)
- 114 kg; max takeoff weight (spraying): 125 kg (as listed in the official spec table)
- Spray tank
- 80 L / 80 kg payload
- Flow rate
- up to 32 L/min (dual pumps)
- Droplet size
- 60–500 μm
- Spray width
- 5–10 m
- Max flight speed
- 20 m/s
- Max takeoff weight
- 136 kg (spraying) / 140 kg (spreading)
- Battery
- B141050 (1050 Wh, 20,000 mAh)
- Precision and repeatability
- RTK-level positioning and radar-assisted sensing support repeatable mission paths, consistent swath spacing, and stable hovering/turning behavior over irregular fields.
- Flight speed
- 18 m/s
- Flow rate
- 32 L/min
- Charging time
- 7 minutes
What to verify before ordering XAG P150 Standard 7KW 6B2C Kit
Use this checklist to reduce model, configuration and integration mismatches.
- Exact robot model, revision and manufacturer part reference
- Payload, reach, mobility, speed or working-envelope requirements
- Battery, charging, runtime and power requirements where applicable
- Controller, SDK/API, network interfaces and software compatibility
- Sensors, end effectors, safety systems and included accessories
- Operating environment, floor/terrain, IP rating and commissioning requirements
XAG P150 Standard 7KW 6B2C Kit manufacturer and technical resources
Manufacturer, regulator and other authoritative references are prioritized for product verification.
XAG official technical resource
Reference material relevant to XAG P150 Standard 7KW 6B2C Kit identity, specifications, compatibility or deployment.
XAG official technical resource
Reference material relevant to XAG P150 Standard 7KW 6B2C Kit identity, specifications, compatibility or deployment.
Frequently asked questions
Key questions for evaluating XAG P150 Standard 7KW 6B2C Kit before purchase.
What is XAG P150 Standard 7KW 6B2C Kit?
Spray width: 5–10 m
What should be checked before ordering XAG P150 Standard 7KW 6B2C Kit?
Exact robot model, revision and manufacturer part reference; Payload, reach, mobility, speed or working-envelope requirements; Battery, charging, runtime and power requirements where applicable.
Are all XAG P150 Standard 7KW 6B2C Kit configurations identical?
No. Hardware revision, software, accessories, modules, handpieces, probes or other options can vary. The written quotation and exact-unit identification should define the supplied configuration.
What is included with XAG P150 Standard 7KW 6B2C Kit?
Only items explicitly listed in the quotation and packing scope should be treated as included. Reference photographs can show accessories or system components that are not part of the final offer.
Can XAG P150 Standard 7KW 6B2C Kit be shipped internationally?
International B2B delivery can be arranged for approved destinations subject to product-specific transport requirements, customs rules and the agreed freight, insurance and delivery terms.
XAG documentation for XAG P150 Standard 7KW 6B2C Kit
Manufacturer names and trademarks are used for product identification. Confirm model-specific instructions, compatibility and regional requirements before deployment.
Procurement support for XAG P150 Standard 7KW 6B2C Kit
Model, part number, condition and supplied configuration can be confirmed before dispatch.
Quotation, packing scope, warranty terms and delivery responsibilities are documented before order approval.
Export packing, freight, insurance and shipment documentation can be coordinated for approved destinations.
Support is available for compatibility questions, installation planning and procurement documentation.
Request a quote for XAG P150 Standard 7KW 6B2C Kit
Include delivery country, quantity, required configuration and target purchase date for a destination-specific offer.
